KTI Networks KGS-1620 Manual do Utilizador

KGS-2421 KGS-1620Console & Telnet Management Interface User,s ManualDOC.101115

14.4 policy delete ... 8714.5 policy add ...

Parameters: <port_list> : Port list or 'all', default: All ports enable : Enable Rx and Tx mirroring disable : Disable Mirroring rx

17. Config (Load/Save of configuration via TFTP) Available Commands: Config Save <ip_server> <file_name>Config Load <ip_server> <

18. SFPDDM (SFP with Digital Diagnostic Monitoring) >SFPDDM help Description: Show SFP with Digital Diagnostic Monit

GlossaryA B C D E F G H I J K L M N O P Q R S T U V W X Y Z AACEACE is an acronym for Access Control Entry. It describes access permission associated

specific traffic properties (Action / Rate Limiter / Port copy, etc) for each ingress port. They will though only apply if the frame gets past the ACE

detect loss of continuity in a network by transmitting CCM frames to a peer MEP. CCMCCM is an acronym for Continuity Check Message. It is a OAM frame

this information to implement IP address or other assignment policies. Specifically the option works by setting two sub-options: Circuit ID (option 1)

EEPSEPS Is an abbreviation for Ethernet Protection Switching defined in ITU/T G.8031. Ethernet Type Ethernet Type, or EtherType, is a field in the

HTTPS is an acronym for Hypertext Transfer Protocol over Secure Socket Layer. It is used to indicate a secure HTTP connection. HTTPS provide authent

IMAP is the protocol that IMAP clients use to communicate with the servers, and SMTP is the protocol used to transport mail to an IMAP server. The cur

Glossary... 103

LLDP is an IEEE 802.1ab standard protocol. The Link Layer Discovery Protocol, is used for network discovery, and works by having the units in the netw

Area Network (LAN), and it is not supported on a Wide Area Network (WAN). The NetBIOS giving each computer in the network both a NetBIOS name and an

Internet exists and is connected. qjoh uses Internet Control Message Protocol (ICMP) packets. The PING Request is the packet from the origin compute

permitted. A VLAN can be configured as a private VLAN. QQCEQCE is an acronym for QoS Control Entry. It describes QoS class associated with a particu

Furthermore you can assign a default class to a port and a queuing mode. Strict queuing means that the higher priority frame will always be served bef

Microsoft Windows networking. Samba can be installed on a variety of operating system platforms, including Linux, most common Unix platforms, OpenVM

SNMP is an acronym for Simple Network Management Protocol. It is part of the Transmission Control Protocol/Internet Protocol (TCP/IP) protocol for net

is used widely in the web pages as well as in the CLI commands. SyncESyncE Is an abbreviation for Synchronous Ethernet. This functionality is used t

enter commands through the Telnet program just as if they were entering commands directly on the server console. TFTP TFTP is an acronym for Trivial

UPnP UPnP is an acronym for Universal Plug and Play. The goals of UPnP are to allow devices to connect seamlessly and to simplify the implementation

1. General 1.1 General Commands General Commands Description Help/? : Get help on a group or a specific command Up : M

etc. The term is promulgated by the Wi-Fi Alliance. WPA WPA is an acronym for Wi-Fi Protected Access. It was created in response to several serious

2. System (System settings and reset options) Available Commands System Configuration [all] [<port_list>]System Name [<name>]System Contac

digits (0-9), minus sign (-). Note: In CLI, no blank or space characters are permitted as part of a name. The first character must be an alpha chara

Syntax:System Timezone [<offset>] Parameters: <offset> : Time zone offset in minutes (-720 to 720) relative to UTC 2.6 Reboot System> R

System>Load help Description: Show current CPU load: 100ms, 1s and 10s running average (in percent, zero is idle). S

3. IP (IP configuration and Ping) Available Commands: IP ConfigurationIP DHCP [enable|disable]IP Setup [<ip_addr>] [<ip_mask>] [<ip_rou

Parameters: <ip_addr> : IP address (a.b.c.d), default: Show IP address <ip_mask> : IP subnet mask (a.b.c.d), default: Show IP ma

4. Port (Port management) Available Commands: Port Configuration [<port_list>] Port State [<port_list>] [enable|disable] Port Mode [<po

(C) 2010 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any direct

4.3 Mode Port> Mode help Description: Set or show the port speed and duplex mode. Syntax:Port Mode [<port_list>

Syntax:Port MaxFrame [<port_list>] [<max_frame>] Parameters: <port_list> : Port list or 'all', default: All ports <max_

4.8 Statistics Port>Statistics help Description: Show port statistics. Syntax:Port Statistics [<port_list>] [&

5. MAC (MAC address table) Available Commands: MAC Configuration [<port_list>] MAC Add <mac_addr> <port_list> [<vid>]MAC Delet

5.3 Delete MAC>Delete help Description: Delete MAC address entry. Syntax:MAC Delete <mac_addr> [<vid>] P

MAC>Learning help Description: Set or show the port learn mode. Syntax:MAC Learning [<port_list>] [auto|disabl

5.9 Flush MAC>Flush help Description: Flush all learned entries. Syntax:MAC Flush

6. VLAN (Virtual LAN) Available Commands: VLAN Configuration [<port_list>]VLAN Aware [<port_list>] [enable|disable]VLAN PVID [<port_lis

6.3 PVID VLAN>PVID help Description: Set or show the port VLAN ID.Syntax:VLAN PVID [<port_list>] [<vid>|

enable : Enable VLAN ingress filtering disable : Disable VLAN ingress filtering (default: Show VLAN ingress filtering) 6.6 Add VLAN>Add help

The information contained in this document is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKSEthernet is a regis

6.9 Status VLAN> Status help Description: VLAN Port Configuration Status Syntax:VLAN Status [<port_list>] [comb

7. PVLAN (Private VLAN) Available Commands: PVLAN Configuration [<port_list>]PVLAN Add <pvlan_id> [<port_list>]PVLAN Delete <pvla

Syntax:PVLAN Delete <pvlan_id> Parameters: <pvlan_id> : Private VLAN ID 7.4 Lookup PVLAN>Lookup help De

8. Security (Security management) Available Command groups: Switch: Switch security Network: Network security AAA: Authentication, Authorization and A

Syntax:Security Switch Auth Configuration 8.1.2.2 Method Security / Switch /Auth> Method help Description: Set or sh

8.1.3.2 Mode [enable|disable] Security / Switch / SSH > Mode help Description: Set or show the SSH mode. Syntax:Secur

8.1.4 HTTPS (Hypertext Transfer Protocol over Secure Socket Layer) Available Commands: Security Switch HTTPSConfigurationSecurity Switch HTTPS Mode [e

enable : Enable HTTPS redirect disable : Disable HTTPS redirect (default: Show HTTPS redirect mode) 8.1.5 SNMP (Simple Network Management Protoco

<oid_subtree>Security Switch SNMP View Delete <index>Security Switch SNMP View Lookup [<index>]Security Switch SNMP Access Add <g

Parameters: 1 : SNMP version 1 2c : SNMP version 2c 3 : SNMP version 3 (default: Show SNMP version) 8.1.5.4 Read Community Security / Switch / S

Table of Contents 1. General...

Parameters: enable : Enable SNMP traps disable : Disable SNMP traps (default: Show SNMP trap mode) 8.1.5.7 Trap Version Security / Switch / SNMP>

Syntax:Security Switch SNMP Trap Destination [<ip_addr_string>] Parameters: <ip_addr_string> : IP host address (a.b.c.d) 8.1.5.10 Trap Au

Syntax:Security Switch SNMP Trap Inform Mode [enable|disable] Parameters: enable : Enable SNMP trap inform disable : Disable SNMP trap inform (defa

8.1.5.15 Trap Probe Security Engine ID Security / Switch / SNMP>Trap Probe Security Engine ID help Description: Show

8.1.5.18 Engine ID Security / Switch / SNMP>Engine ID help Description: Set or show SNMPv3 local engine ID. Syntax:S

8.1.5.21 Community Lookup Security / Switch / SNMP>Community Lookup help Description: Lookup SNMPv3 community entry.

Delete SNMPv3 user entry. Syntax:Security Switch SNMP User Delete <index> Parameters: <index> : entry index (1-64) 8.1.5.24 User Changekey

Description: Add or modify SNMPv3 group entry. The entry index key are <security_model> and <security_name>. Syntax:Security Switch SNMP G

Security / Switch / SNMP>View Add help Description: Add or modify SNMPv3 view entry. The entry index key are <vie

Security / Switch / SNMP>Access Add help Description: Add or modify SNMPv3 access entry. The entry index key are <

5.1 Configuration... 235.2 Add...

Description: Lookup SNMPv3 access entry. Syntax:Security Switch SNMP Access Lookup [<index>] Parameters: <index> : entry index (1-64) 8.2

Security Network Psec Port [<port_list>] Parameters: <port_list> : Port list or 'all', default: All ports 8.2.2 NAS (Network Acc

Parameters: enable : Globally enable 802.1X disable : Globally disable 802.1X (default: Show current 802.1X global enabledness) 8.2.2.3 State Secur

Set or show the period between reauthentications. Syntax:Security Network NAS ReauthPeriod [<reauth_period>] Parameters: <reauth_period>

Time in seconds before a MAC-address that failed authentication gets a new authentication chance.Syntax:Security Network NAS Holdtime [<hold_time&g

8.2.3 ACL (Access Control List)Available Commands: Security Network ACLConfiguration [<port_list>]Security Network ACL Action [<port_list>

[<port_copy>] [<logging>] [<shutdown>] Parameters: <port_list> : Port list or 'all', default: All ports perm

Description: Add or modify Access Control Entry (ACE). If the ACE ID parameter <ace_id> is specified and an entry with this ACE ID already exist

arp : ARP keyword <sip> : Source IP address (a.b.c.d/n) or 'any' <dip> : Destination IP address (a.b.c.d/n) or 'any'

Show ACE, default: All ACEs. Syntax:Security Network ACL Lookup [<ace_id>] Parameters: <ace_id> : ACE ID (1-128) 8.2.3.8 Clear Security /

8.1.4 HTTPS (Hypertext Transfer Protocol over Secure Socket Layer)... 368.1.4.1 Configuration...

Security AAA Statistics [<server_index>]8.3.1 Configuration Security / AAA > Configuration help Description:

Description: Set or show RADIUS authentication server setup. Syntax:Security AAA RADIUS [<server_index>] [enable|

9. STP ( Spanning Tree Protocol ) Available Commands: STP ConfigurationSTP Version [<stp_version>]STP Txhold [<holdcount>]STP MaxHops [<

9.2 Version STP>Version help Description: Set or show the STP Bridge protocol version. Syntax:STP Version [<stp_v

Description: Set or show the CIST/MSTI bridge maximum age. Syntax:STP MaxAge [<max_age>] Parameters: <max_age> : STP maximum age time (6-

Syntax:STP bpduGuard [enable|disable] Parameters: enable|disable : enable or disable BPDU Guard for Edge ports 9.9 recovery STP>recovery help

Syntax:STP Status [<msti>] [<port_list>] Parameters: <msti> : STP bridge instance no (0-7, CIST=0, MSTI1=1, ...) <port

Syntax:STP Msti Add <msti> <vid> Parameters: <msti> : STP bridge instance no (0-7, CIST=0, MSTI1=1, ...) <vid> : VLAN ID (

STP Port Edge [<port_list>] [enable|disable] Parameters: <port_list> : Port list or 'all', default: All ports enable : Config

Set or show the MSTP restrictedRole port parameter. Syntax:STP Port RestrictedRole [<port_list>] [enable|disable] Parameters: <port_list>

8.1.5.30 View Delete ... 488.1.5.31 View Lookup...

STP>Port Statistics help Description: Show STP port statistics. Syntax:STP Port Statistics [<port_list>] Param

Syntax:STP Msti Port Cost [<msti>] [<port_list>] [<path_cost>] Parameters: <msti> : STP bridge instance no (0-7, CI

10. IGMP (Internet Group Management Protocol snooping) Available Commands: IGMP Configuration [<port_list>]IGMP Mode [enable|disable]IGMP State

10.3 State IGMP>State help Description: Set or show the IGMP snooping state for VLAN. Syntax:IGMP State [<vid&g

<port_list> : Port list or 'all', default: All ports enable : Enable IGMP fast leave disable : Disable IGMP fast leave (defaul

Syntax:IGMP Groups [<vid>] Parameters: <vid> : VLAN ID (1-4095) 10.9 Status IGMP>Status help Description

11. Aggr ( Link Aggregation ) Available Commands: Aggr ConfigurationAggr Add <port_list> [<aggr_id>]Aggr Delete <aggr_id>Aggr Lookup

Parameters: <aggr_id> : Aggregation ID 11.4 Lookup Aggr>Lookup help Description: Lookup link aggregation. Synt

12. LACP ( Link Aggregation Control Protocol ) Available Commands: LACP Configuration [<port_list>]LACP Mode [<port_list>] [enable|disable

Description: Set or show the LACP key. Syntax:LACP Key [<port_list>] [<key>] Parameters: <port_list>

8.3.4 RADIUS... 608.3.5 Statistics...

Description: Show LACP Statistics. Syntax:LACP Statistics [<port_list>] [clear] Parameters: <port_list> : P

13. LLDP ( Link Layer Discovery Protocol ) Available Commands: LLDP Configuration [<port_list>]LLDP Mode [<port_list>] [enable|disable|rx|

disable : Disable LLDP rx : Enable LLDP reception only tx : Enable LLDP transmission only (default: Show LLDP mode) 13.3 Optiona

13.5 Hold LLDP>Hold help Description: Set or show LLDP Tx hold value. Syntax:LLDP Hold [<hold>] Parameters: &l

Show LLDP neighbor device information. Syntax:LLDP Info [<port_list>] Parameters: <port_list> : Port list or 'all', default: All

14. LLDPMED (Link Layer Discovery Protocol Media) Available Commands: LLDPMED Configuration [<port_list>]LLDPMED Civic [country|state|county|cit

Syntax:LLDPMED Civic [country|state|county|city|district|block|street|leading_street_di rection|trailing_street_suffix|str_suf|house_no|house_no_suffi

Syntax:LLDPMED ecs [<ecs_value>] Parameters: <ecs_value> : The value for the Emergency Call Service 14.4 policy delete LLDPMED > polic

guest_voice : Guest Voice to support a separate limited feature-set voice service for guest users and visitors with their own IP Telephony hands

Syntax:LLDPMED port policies [<port_list>] [<policy_list>] Parameters: <port_list> : Port list or 'all', default: All

10.4 Querier ... 7310.5 Fastleave...

Set or show LLDP-MED Coordinates map datum. Syntax:LLDPMED Datum [wgs84|nad83_navd88|nad83_mllw] Parameters: wgs84|nad83_navd88|nad83_mllw : WGS84nad

Description: Set or show if the current value of the global medTansmitEnable variable (Section Section 11.2.1, TIA 1057). Syntax:LLDPMED debug_med_tra

15. QoS ( Quality of Service ) Available Commands: QoS Configuration [<port_list>]QoS Classes [<class>]QoS Default [<port_list>] [&l

Syntax:QoS Classes [<class>] Parameters: <class> : Number of traffic classes (1,2 or 4) 15.3 Default QoS>Default help

QoS QCL Port [<port_list>] [<qcl_id>] Parameters: <port_list> : Port list or 'all', default: All ports <qcl_id>

<tos_list> : IP ToS list (0-7) tag_prio : VLAN tag priority keyword <tag_prio_list> : VLAN tag priority list (0-7) <clas

Parameters: <port_list> : Port list or 'all', default: All ports strict : Strict mode weighted : Weighted mode (default: Show QoS mode

Set or show the port shaper.Syntax:QoS Shaper [<port_list>] [enable|disable] [<bit_rate>] Parameters: <port_list> : Port list or &ap

15.15 Storm Broadcast QoS>Storm Broadcast help Description: Set or show the multicast storm rate limiter. Syntax:QoS

16. Mirror (Port mirroring) Available Commands: Mirror Configuration [<port_list>]Mirror Port [<port>|disable]Mirror Mode [<port_list&g